Clone A Willy Review

We loved the idea of the Clone A Willy product, the actual making another version of Steve’s penis that even vibrates sounded so brilliant we ended up trying this more than once. Find out what happened in our Clone a Willy Review below…

Instructions

We cannot stress this enough, after multiple attempts of making a mould it is extremely important to read the instructions cover to cover multiple times before even attempting this product as you will not have time to check the instructions when in the middle of creating the Clone A Willy. You also have to follow these instructions word for word as any slight change can make it fail.

We would also highly advise you to shave or at least trim the pubic area before using this product as the mould can set onto the hairs and you will need to pluck out the hairs afterwards and that is a bit eye watering.

Preparation

After reading the instructions we found it is very important to lay out all the parts of the Clone A Willy kit in a row and in the order which you need to do them in. This may seem a little drastic  but as soon as you start doing the mould you are really fighting against the clock and without this preparation beforehand we doubt anyone would be able to get a good clone out of it.

To get started it is important that you are very erect and that’s where your willing helper can lend a helping hand or mouth. Once erect you have to mark the erect length on the tube and then cut the tube down from that mark.

After cutting the tube the next step is to get the water to an exact temperature, thankfully a thermometer is included inside the pack. It is important that as soon as you get the required temperature you need to mix in your mould solution and stir it for a minute, put the solution into the tube, and then put your penis into the tube.

Inserting

During this entire time you need to stay very erect, this is where a willing helper or porn is very important. We found the best way to do this part was to have your helper do all the mixing whilst the person being moulded concentrates on keeping hard either by watching porn or some other method.

Once the penis is inside the Clone A Willy tube you also need to be completely erect for a few minutes whilst the mould sets, this may sound easy but actually it is not as the heat from the mould and the really odd feeling of the mould on your penis is quite a passion killer so we found it’s best to have the helper to either play with themselves or do a sexy strip tease to make sure the penis stays erect.

It is also important that the penis is kept away from the sides of the tube, this can be quite difficult and our first attempt at this failed and we ended up with a mould with a flat edge because of it. The instructions say you should slowly turn the tube if you think the penis is touching the side until it’s not touching.

On the instructions inside the pack it says you should really wait at least 2 hours before putting the 2 tubs of solution into your now set mould, oddly it says this after saying ‘Now mix and put the 2 tubs in’ so some people will not wait the suggested 2 hours as it was really a side note on the instructions. Luckily we spotted this and waited the suggested 2 hours. After which you need to place the vibrator inside you then have to wait 24 hours before seeing the final outcome, so you need to be patient!

Outcome of the Clone a Willy

After the 24 hours we couldn’t wait to see the end result but it wasn’t what we expected at all unfortunately, it didn’t really Steve’s penis and was very bitty and flaky and really not OK to use in sexual activities. As Steve’s penis touched the sides on the tube during moulding the included vibrator actually popped out of the set mould.

After our first failed attempt we purchased Clone a Willy again but we fared quite much better, we chose not to put the vibrator in as we felt it was one of the reasons why the original didn’t work very well. Instead we inserted the mixer stick as the handle. This time the set mould did look a lot more like my penis compared to the first attempt but it came out smaller than Steve’s size as he struggled keeping erect, it was very flaky, had lots of bits missing and little holes everywhere on the product.

Overall Opinion

It was fun creating the Clone A Willy, so it wasn’t a total loss and I think we’ll always laugh about our attempts and how unlike Steve’s penis they became. It’s a shame the moulds didn’t turn out looking great and that they couldn’t be used in our play due to the flakiness of the finished product. We may try this product again in the future and you never know it might be 3rd time lucky!

Click Here to get the Clone A Willy for a Low Price >

Click Here for more Clone A Willy Reviews and Videos >

Disclosure: This toy was given to us free of charge in return for this Clone A Willy Review. All opinions expressed are our own, and were not influenced in any way.